How to do a fuel filter change on w123 – Petrol engine

Fuel Filter w123
Reading Time: 4 minutes

How to change the Fuel filter

So how do you change the fuel filter? It is in theory simple, but in practice it can be quite messy and also tricky to fully access in the rear end fuel delivery system on the w123 chassis. You also need to make sure you have as low fuel as possible or drain the fuel tank dry.

WARNING :
There is a high explosion and fire risk when dealing with petrol fumes, so don’t light up your cigarette and avoid sparks!

Preparation 

Make sure you inspect the fuel delivery system, since a lot of parts there might need to be changed along with the fuel filter, and since you are already draining fuel you don’t want to do this again in 2 months. See the older article on How to re-haul the rear fuel delivery system on w123 (gasoline)

Part requirements:

  • New Fuel filter
  • Optional parts:
    • Fuel delivery assembly rubber bushings – I highly recommend to change these
    • Fuel pump
    • Fuel accumulator
    • Fuel hoses
      • Main tank hose
      • High pressure hose
      • Low pressure hoses
    • Fuel hard line and fittings

Tools:

  • Spanners
  • Sockets
  • Hose clamp

Procedure 

You need to access the rear end fuel delivery system on the rear right end of the car. It consists of the fuel pump, fuel filter and the fuel accumulator. They are suspended from 4 rubber bushings secured in a weird metal clamp. It is partly hidden behind a plastic cover near the right rear wheel.

Removal 

Start by removing the battery, trust me, you dont’ want sparks while working under the car with petrol fumes! And don’t smoke!

Then jack up the rear end of the car up on jack stands and block the front wheels from rolling. As extra safety measure I always leave the jack in raised position on the same side as I will be working.

Remove the rear right wheel and you have better access to the fuel delivery system. Locate the plastic cover which is held by a few screws, use a long thin socket extension to remove these.

Fuel delivery assembly w123

Now you have to drain the fuel from the tank to avoid petrol spills and excessive fumes. This can either be done with using a vacuum pump with a  hose down into the filler neck, or by disconnecting the main hose to the fuel pump. It will also leak fuel from the delivery line to the engine, and this can be blocked from continuously dripping with a hose clamp on the high pressure hose. Make sure the clamp is of high quality with no sharp edges, since a new high pressure hose is quite expensive.

Fuel filter removed
Fuel filter removed. Notice the high pressure hose is clamped.

When the fuel is drained. You can start by loosening the 2 lines that connects to the fuel filter. The left side (from rear) is the high pressure line and the right is the hard line. Notice the position of the two copper washers on the hard line fitting.  A lot more fuel will now drain out from the filter so take care. It is possible to remove the filter from the cage without removing the whole assembly.

Rubber bishings fuel pump w123
Installing new rubber bushings for fuel pump assembly.

If you need to also change the rubber bushings, then change them one by one and you don’t have to take the whole assembly down. Alternatively to get better access you can secure the assembly with zip ties while changing them.

Fuel delivery assembly w123
New bushings installed

Installation 

Installation is pretty much reverse of removal, but you have to remember to use the new copper washers that followed with the new filter. Also I found that you need to torque down the screw between the hard line and the filter for it to not leak.

After everything is put together and you have put some fuel in the tank, try to start the car, it should not take long for the engine to fire up after you crank it. The fuel pump is pretty quick pushing fuel through. When the car is running, go back and inspect carefully if fuel is leaking and check for any wetness.

New fuel filter installed on w123
New fuel filter installed.

If it’s dripping or you can see wetness, shut off the car. Tighten the bolts, wipe off the fuel so it’s completely dry and try again. I had to redo this step twice before it was properly sealed, and the leak was indeed between the new copper washers and the hard line. The copper washers will actually start to seal better when exposed to moisture and some small corrosion will start forming in the gaps.

Be sure to check for any wetness under the rear end of your car after you parked it the first times, since leaking fuel is bad for your wallet and is a potential fire hazard.

Cheers, Robs out! 

Author: Robs

Passionate about vintage Mercedes Benz where driving, maintaining and learning new things and teaching others on the black arts of car maintenance.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.